Clearcoats

• Enlarge Image

Products

HP Quick Finish Clearcoat
4.2 VOC

• Gallon (#530-01)
  - Quantity: 4/cs

• Quart (#530-04)
  - Quantity: 12/cs

HP Quick Finish Activator

• Quart (#531-04)
  - Quantity: 12/cs

• Quart (#531-16)
  - Quantity: 12/cs

Product Flyers

#530 HP Quick Finish Clearcoat 4.2 VOC

Product MSDS

530-01

530-04

531-04

531-16

Technical Data Sheet

#530 HP Quick Finish Clearcoat 4.2 VOC

530 Mobile TDS & MSDS

531 Mobile TDS & MSDS

#530 HP QUICK FINISH CLEARCOAT
4.2 VOC

PRODUCT DESCRIPTION
Designed to provide the shortest cycle times for maximum efficiency. It flows out to a smooth, durable finish with excellent gloss. Intended for spot, small, 1-2 panel in size jobs.

BASECOAT
Apply basecoat as per manufacturerʼs mixing and application instructions. Allow sufficient flash times before applying #530. Inadequate flash time will affect the performance of the clear.

MIXING RATIO (4:1)
Mix 4 parts #530 Clearcoat to 1 part #531 Activator.

SURFACE PREPARATION
1. Allow the final coat of basecoat to dry to touch prior to applying clearcoat.
2. Use a tack cloth to remove any surface contaminates that may have settled on the basecoat.
3. Apply Clearcoat.

APPLICATION
Apply 2 full wet coats at 40-50 psi at the gun (6-10 psi when using HVLP at the cap), NO flash
between coats. IMPORTANT: NOT FOR USE ON MORE THEN 1 PANEL.

DRY TIMES AT 77° F
DUST FREE 5 - 10 MINUTES
TO SAND 1 HOUR
TO BUFF 1 HOUR OR LESS
DELIVER 2 1/2 - 3 HOURS

RECOATING
#530 may be recoated after an overnight dry at 77° F

POLISHING
2 COATS 45 MINUTES
3 COATS 60 MINUTES
Temperature, humidity and film thickness will affect buff times. If extreme color sanding and
buffing is needed allow overnight dry time.

POT LIFE
Pot life will be about 1-2 hours at 77° F.

ACCELERATOR
Not Recommended.

BLENDING
Dry edges can be blended in with the use of a Blend Edge Blender. Refer to the technical data sheet.

FISH EYE
The use of fish eye eliminator is strongly discouraged. If a fish eye additive is needed, use urethane fish eye eliminator, mix 1/2 ounce per sprayable quart. Use no more than necessary as it will directly affect flow out of #530

EQUIPMENT CLEAN-UP
Clean equipment immediately after use with a high quality lacquer thinner or urethane reducer.

TECHNICAL DATA
Mixing Ratio: 4 parts #530
1 part #531
Viscosity (RTS): 18-20 seconds #2 Zahn
Weight Solids (RTS): 36.14%
Film Build: 1.0 - 1.5 mils per full wet coat
Coverage: 506 sq. ft. per gallon @ 1 dry mil
V.O.C. as Delivered: Regulatory Regulatory Material Material
VOC in LBS./GAL. VOC in G./L. VOC in LBS./GAL. VOC in G./L.
#530 4.5 534 3.2 387
#531 3.5 422 3.5 422
V.O.C. (RTS):
#530/#531 4.2 506 3.6 394
Disposal/Safety: see MSDS for this product
Humidity Resistance: Excellent
Salt Spray Resistance Excellent
NOTE: ADVANTAGE products are not recommended for use in temperatures below 60° F. Use below these temperatures will effect dry times and performance.

FOR INDUSTRY USE ONLY
Read MSDS Before Use
The contents of the package must be blended with other components before the product can be used. Any mixture of components will have hazards of all components. Before opening the packages, read all warning labels. Follow all precautions. The material is designed for application only by professionally trained personnel using proper equipment under controlled conditions, and is not intended for sale to the general public.
SEE MSDS AND PRODUCT LABELS FOR ADDITIONAL SAFETY INFORMATION.

Call 1-87REFINISH (1-877-334-6474) to
find your local Advantage Refinish Products
supplier. Or visit our website:
www.advantagerefinishproducts.com