- Home
- Clearcoats
- #530 HP Quick Finish Clearcoat 4.2 VOC
- #535 Production Clearcoat 4.4 VOC
- #545 High Solids (HS) Clearcoat 4.2 VOC
- #550 Universal Urethane Clearcoat 4.4 VOC (NR)
- #555 Universal Quick Finish Clearcoat 4.2 VOC (NR)
- #570 Production Clearcoat 2.1 VOC
- #575 Euro Max High Solids Clearcoat 4.2 (NR)
- #580 Euro Max High Solids Clearcoat 2.1 VOC
- #675 Euro Max HS Glamour Clearcoat 4.2 VOC
- #590 Quick Finish Speed Clearcoat 2.1 VOC
- Primer Surfacers
- Custom Single-Stage Paints
- Series 700 Custom Colors 2.8 VOC
- #600 Gloss Black
- #601 Flat Black
- #603 Gloss White
- #606 Fleet White
- #607 Oxford White
- #608 Charcoal Mist Metallic
- #609 Brilliant Black Pearl
- #610 Viper Red
- #611 Swift Red
- #612 Candy Apple Red
- #613 Wine Red Mica
- #614 Red Crystal Pearl
- #615 Omaha Orange
- #616 Imperial Orange Metallic
- #617 Corvette Yellow
- #618 Jaguar Racing Green
- #619 Dark Green
- #620 Light Blue Metallic
- #621 Teal Metallic
- #622 Spectra Blue Metallic
- #623 Hi-Lite Blue Pearl
- #624 Dark Blue Metallic
- #625 Gold Metallic
- #626 Champagne Metallic Pearl
- #627 Galaxy Silver
- Aerosol Paint Sprays
- Thinners
- Hardeners
- Reducers
- Solvents and Cleaners
- Fillers
- Putty
- Body Shop Supplies
- Advantage Distributors
(1-877-334-6474)
website designed & maintained
by RHCreative.com
Clearcoats
#590 QUICK FINISH SPEED
CLEARCOAT 2.1 VOC
PRODUCT DESCRIPTION:
ADVANTAGE #590 QUICK FINISH SPEED Clearcoat 2.1 VOC was designed to offer ease of application, great flow and
leveling, superior gloss & DOI in a highly productive 2K urethane clearcoat. Under the proper conditions #590 can be
polished in as little as 90 minutes.
SURFACE PREPARATION:
Apply Undercoats and Basecoat per manufacturer’s instruction. Over OEM or completely cured previously painted
substrates scuff with a gray scuff pad or 600 grit then wipe clean with Wax & Grease Remover.
Allow basecoat adequate flash time (follow manufacturer’s recommendation). Follow basecoat manufacturer’s
recommendation for recoat intervals.
MIXING DIRECTIONS:
Mix 4 parts #590 clear with 1 part #591, #592, or #593 activator by volume. Activator selection should be based on
the size of the part to be painted and the temperature of both the air and part at time of painting.
| APPLICATION DIRECTIONS: | |
| Number of Coats: | 2-3 wet coats |
| Application Density: | Medium-wet to wet |
| Overlap: | 50% |
| Flash: | Follow recommendations in "Dry Time" section |
| 10 – 15 mins in-between coats (@ 72° F / 22° C) | |
| Application Conditions | |
| Minimum Temp: | 50°F (Substrate Temp.) |
| Max Temp: | 100°F (Substrate Temp.) |
| Ambient Humidity: | Less than 80% preferred |
| Film Thickness Range: | |
| Dry: | 1 mil - 4 mils |
| Wet: | 3 mils - 4 mils |
| ADDITIVES: | |
| ACCELERATOR: N/A | FISHEYE: N/A |
| FLEX ADDITIVE: Not required | Note: Do not spray when surface temperature is below 50°F. |
SUBSTRATES:
Commercially available acrylic/cab basecoats with a VOC less than 6.6 lbs/gal. Properly prepared previously painted substrates.
| GUN SETUPS: | AIR PRESSURES | ||
| CONVENTIONAL | CONVENTIONAL @ Gun | PANEL | OVERALL |
| Gravity Feed: 1.3 mm - 1.5 mm |
Gravity Feed: | 35-40 psi | 45 psi |
| Siphon Feed: 1.6 mm - 1.8 mm |
Siphon Feed: | 35-45 psi | 45-50 psi |
| HVLP: 1.3 mm - 1.5 mm |
HVLP @ Cap: | 6-8 psi | 9-10 psi |
| FLASH/DRY TIMES: | |||
| Dry Times: | 591 @ or above 77°F |
592 @ or above 85°F |
593 @ or above 95°F |
| Flash Between Coats | 5-10 min | 5-10 min | 5-10 min |
| Dust Free | 10-15 min | 10-15 min | 10-15 min |
| Sand/Polish | 1.5-2 hours | 1.5-2 hours | 1.5-2 hours |
| #591 | #592 | #593 | |
| Purge time before applying heat |
0-15 min | 0-15 min | 0-15 min |
| Force Dry Time | 20 min @ 165°F | 20 min @ 165°F | 20 min @ 165°F |
| Sand and Buff | After Cool Down | After Cool Down | After Cool Down |
CLEAN-UP & STORAGE:
Clean spray equipment immediately after use with Acrylic Lacquer Thinner or Urethane Reducer. Do not leave material in
spray gun.
| PRODUCT TECHNICAL DATA (READY TO SPRAY): | |
| Mix Ratio: | 4 parts clearcoat: 1 part activator |
| VOC: | 546 Spot, 547 Panel, 548 Multi-Panel |
| Catalyst: | 2.1 lbs/gal |
| Solids (Ready to Spray) | 18-20 seconds #2 Zahn |
| By Volume: | 33.1% |
| Viscosity: | 17-19 seconds Zahn #2 |
| Flash Point: | -4°F |
| Film Build: | 1.0 mils per full wet coat |
| Theoretical Coverage: | 531 ft2/gal @ 1 mil thickness |
| Pot Life: | When properly covered at 77°F, #590 will maintain a sprayable viscosity for at least 1-3 hours depending on activator selection. |
SAFETY INFORMATION - FOR PROFESSIONAL/INDUSTRY USE ONLY:
DANGER! FLAMMABLE! HARMFUL IF INHALED - MAY AFFECT THE BRAIN OR NERVOUS SYSTEM, CAUSING DIZZINESS, HEADACHE OR NAUSEA. IRRITATES
EYES, SKIN AND RESPIRATORY TRACT. Contents are FLAMMABLE. Vapors may cause flash fires. Keep away from heat, sparks, and open flame. During use and
until all vapors are gone: Keep area ventilated - Do not smoke - Extinguish all flames, pilot lights, and heaters - Turn off stoves, electric tools and appliances, and
any other sources of ignition. SEE CONTENTS STATEMENT ELSEWHERE ON LABEL. VAPOR HARMFUL. Use only with adequate ventilation. This product must
be used with an appropriate catalyst. Follow the respirator requirement and instructions on the catalyst. Avoid contact with eyes and skin. Wash hands after
using. Keep container closed when not in use. Do not transfer contents to other containers for storage. FIRST AID: If INHALED: If affected, remove from exposure.
Restore breathing, Keep warm and quiet. If on SKIN: Wash affected area thoroughly with soap and water. Remove contaminated clothing. Launder before re-use.
If in EYES: Flush eyes with large amounts of water for 15 minutes. Get medical attention. If SWALLOWED: Get medical attentionimmediately. DELAYED EFFECTS
FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately
concentrating and inhaling the contents can be harmful or fatal. This product must be mixed with other components before use. Before opening the packages,
READ AND FOLLOW WARNING LABELS ON ALL COMPONENTS. DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN. FOR PROFESSIONAL
USE ONLY. SEE MATERIAL SAFETY DATA SHEET. Prop 65 Statement: WARNING: This product contains a chemical known to the state of California to cause
cancer, birth defects or other reproductive harm. Manufacturer’s Exclusive Limited Warranty: For Industrial use only by professional, trained personal using
proper safety protective equipment. Not for sale to, or use by, the general public. Manufacturer warrants that its products are free from defect in material and
workmanship at the time of sale. In the event that any product is proved by objective testing and analysis to have been defective at the time of sale, upon the
return of the defective product, the manufacturer shall replace the product at no cost, excluding the shipping costs, as the exclusive remedy. This warranty does
not cover damage caused by accident, misuse, improper application, improper combination of products or tampering. ALL IMPLIED WARRANTIES WHETHER IT
BE OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. THIS WARRANTY EXCLUDES ALL INCIDENTAL AND
CONSEQUENTIAL DAMAGES. KEEP OUT OF REACH OF CHILDREN. REFER TO MATERIAL SAFETY DATA SHEET. EMERGENCY MEDICAL &
SPILL CONTROL CHEMTREC (800) 424-9300
Made in the USA for ABI/Autobody Brands International a division of IAMG/International Autobody Marketing Group
Scottsdale, AZ 85257 www.autobodybrands.com.
Call 1-87REFINISH (1-877-334-6474) to
find your local Advantage Refinish Products
supplier. Or visit our website:
www.autobodybrands.com